How To Change A Window Motor

Download Commodity

If ane of the power windows in your vehicle fails to function, it may be the event of a cleaved power window motor. If yous have identified the motor as the culprit, replacing information technology is fairly straight forward, though it can be time consuming. It is recommended that y'all review a service transmission specific to your vehicle when replacing the motor, as the methods used to disassemble motorcar doors tin vary from vehicle to vehicle.

1
Remove the interior door panel. About interior door panels are held in identify with plastic interior fasteners. You can remove these fasteners by pulling on them until they pop out of their holes. Interior panels may also exist held on with metallic or plastic screws or even bolts.^[ane]
- If y'all tin can't easily place what kind of fasteners are on your door console, refer to the vehicle's service transmission.
- Plow screws or bolts counter clockwise to loosen them, and then pull the panel astern off of the door.
2
Gently remove the plastic door cover. Beneath the door panel you lot will find a thin, translucent layer of plastic. This cover protects the interior of the vehicle from whatever water that may splash into the door from in a higher place and below. Carefully pull the door off of the sticky portions that secure it.^[two]
- Try not to tear the embrace every bit you will demand to reinstall information technology later replacing the window motor.
- Replacement covers tin can be purchased at your local auto parts store.
Advertisement
iii
Locate the window mounting bolts. Depending on the pattern of your door, there are a few different places the window mounting bolts may be, but information technology should exist fairly apparent when looking into the door. Look for the bolts attaching the window itself to the machinery that raises and lowers it.^[3]
- Y'all may need to use a flashlight to look into the service ports on the door.
- Different shaped doors will place the bolts in different locations.
4
Movement the window if necessary to access the bolts. In some cases, you lot may need to raise or lower the window in lodge to access the bolts. Turn the key in the ignition of the vehicle without starting the engine to move the window if need be.^[iv]
- Raise or lower the window using the ability window buttons if possible.
- If the motor is broken, y'all can strength the window upwardly or downward by paw.
5
Remove the bolts while a friend supports the window. Use the advisable sized socket or open ended wrench to remove the window mounting bolts, but inquire a friend to hold the window up as you do to prevent it from falling down once it's asunder.^[v]
- You lot may be able to hold the window in identify as you lot loosen the bolts yourself, merely it'southward dangerous.
- Dropping the window freely could result in the glass breaking.
6
Raise the window up into the door frame. Have your friend raise the window up into the door frame as though y'all had rolled it up commonly. Ask them to agree the window in identify until you are able to secure it.^[vi]
- Pressing 1 palm on each side of the drinking glass will allow your friend to hold the window up.
7
Utilize masking record to secure the window in place. With your friend belongings the window up, pull off three or iv strips of masking tape that are each about a foot long. Stick the strips to the window on each side over the door frame to hold the window upwardly while y'all work.^[7]
- One time the window is secured with the tape, you lot can have your friend let go.
- Be sure the tape will hold the weight of the window before your friend releases it.

1
Remove the window regulator bolts. The window regulator runs the width of the interior portion of the door and moves back and forth in order to enhance and lower the window. Find the bolts that concord the regulator to the door and remove them with a socket or open ended wrench.^[8]
- Set the bolts aside someplace safe, where you will easily be able to decide which bolts were for the regulator.
- Get out the regulator laying inside the door'south interior for now.
2
Locate and remove the window motor mounting bolts. The power window motor is much smaller than the regulator, but should exist located shut by. In most applications, the bolts securing the motor to the door are the same size equally the regulator mounting bolts. Remove them and set them someplace safe as well.^[ix]
- Fifty-fifty if the bolts have the same size head, they may not be the same length, so exist certain to set up them aside separately from the regulator mounting bolts.
iii
Disconnect the motor wiring harness connector. The power window controls attach to the motor and regulator via a wiring pigtail connector. Press the tab downwardly to disconnect the pigtail then pull them apart to disconnect the motor.^[10]
- Be careful non to intermission the tab that holds the wiring harness together.
- Pull the pigtail autonomously at the prune, not on the wires. Pulling on the wires could pull them out of the pigtail.
four
Remove the motor and regulator through the access port. With the pigtail disconnected, the power window motor and regulator volition no longer be connected to anything inside the door. Reach into the big access port and pull them each out.^[eleven]
- The two are connected, so pulling one volition remove them both.
- Be conscientious not to harm the regulator if you are just replacing the motor.
5
Connect the regulator to the new motor. If you are only replacing the power window motor and non the regulator itself, you will need to disconnect it and connect it to your new power window motor. Visually inspect the two to make certain the new motor matches the old one, then swap the regulator.^[12]
- Different vehicles volition apply different methodology to secure the regulator to the window motor.
- Refer to the service manual for your vehicle if you lot are unsure of how to disconnect the regulator.

1
Slide the new motor and regulator back into identify. Insert the power window motor and regulator back into the main service port in the door in exactly the contrary society that you removed them in when disassembling the door.^[13]
- Orient each component and then the holes for the mounting bolts will line up with the holes in the interior of the door.
two
Supersede the mounting bolts. Agree each component in the appropriate position equally y'all return the mounting bolts that secure both the power window motor and the regulator. Thread each bolt in by hand first, then employ a wrench to tighten them.^[xiv]
- If a bolt doesn't thread it properly, remove information technology and effort again to prevent cross-threading them.
- The bolts don't have to be extremely tight, just tight enough to prevent them from vibrating loose as y'all drive.
3
Reconnect the electrical connector. One time the power window motor and regulator are both mounted securely to the door, connect the wiring from the motor to the pigtail you disconnected previously. This volition reconnect the ability window switches and ability source.^[fifteen]
- Be sure the connections fit together. If not, you lot don't have the correct power window motor.
iv
Remove the masking tape and lower the window back downwardly. Ask your friend to hold the window once more. Once they are in place, remove the masking tape that is holding the window upward in the door frame. In one case the tape is removed, your friend can lower the window back into the mounting subclass.^[16]
- Brand certain your friend has a grip on the window before removing the tape that secures information technology.
- You tin can utilise adhesive remover similar Goo Gone on the window if the tape left any residue once yous are done.
five
Insert the window mounting bolts. Have your friend hold the window in the correct place so the holes in line upwardly with the holes for the window mounting bolts. Once the window is in place, thread the window mounting bolts in by hand, before tightening them with the wrench.^[17]
- Be sure your friend holds the window in place until the mounting bolts are in place.
- Have your friend let get gradually to ensure the bolts are property the window properly.
half dozen
Reinstall the plastic liner and interior console. Once the window is mounted again, you can reattach the plastic interior comprehend, and then reinstall the interior panel over the door. Insert the door mounting bolts or snaps to hold it in place.^[18]
- Once the door is reassembled, reconnect the bombardment.
- Starting time the engine and test the window.

Advertizing

Add New Question

Question

If a regulator has a helper bound on information technology, practise I demand to accept the whole regulator out to secure the arms, or can I replace the motor while it is in the car?

Depending on the pattern of the vehicle, yous will probable need to remove the regulator also as the motor when replacing it.
Question

Is the window regulator motor from a 2001 Ford Escape interchangeable with a 2002 Ford Explorer?

They might be. The best way to know for sure is to bank check the part numbers for each and see if they match. If they do non, they are not interchangeable.
Question

Where is the fuse located?

The_general_s

Community Answer

Fuses are usually in one of three areas: the engine bay, trunk area, about steering wheel.